View 74LV4067PWDH_7505096.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

74lv4067 16-channel analog multiplexer/demultiplexer product specification supersedes data of 1997 jul 15 ic24 data handbook 1998 jun 23 integrated circuits
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 2 1998 jun 23 853-1997 19618 features ? optimized for low voltage applications: 1.0 to 6.0 v ? accepts ttl input levels between v cc = 2.7 v and v cc = 3.6 v ? low typ aono resistance: 60 at v cc gnd = 4.5 v 90 at v cc gnd = 3.0 v 145 at v cc gnd = 2.0 v ? typical abreak before makeo built in ? output capability: non-standard ? i cc category: msi description the 74lv4067 is a low-voltage cmos device and is pin and function compatible with 74hc/hct4067. the 74lv4067 is an 16-channel analog multiplexer/demultiplexer with four address inputs (s o to s 3 ), an active low enable input (e ), sixteen independent inputs/outputs (y 0 to y 15 ) and a common input/output (z). the 74lv4067 contains sixteen bidirectional analog switches, each with one side connected to an independent input/output (y 0 to y 15 ) and the other side connected to a common input/output (z). with e low, one of the sixteen switches is selected (low impedance onstate) by s 0 to s 3 . all unselected switches are in the high impedance off-state. with e high, all switches are in the high impedance off-state, independent of s 0 to s 3 . the analog inputs/outputs (y 0 to y 15 , and z) can swing between v cc as a positive limit and gnd as a negative limit. vcc gnd may not exceed 6.0 v. quick reference data gnd = 0 v; t amb = 25 c; t r =t f 2.5 ns symbol parameter conditions typical unit t pzh /t pzl turn aono time e to v os s n to v os c l = 15 pf r l = 1k v cc = 3.3 v 25 27 ns t phz /t plz turn aoffo time e to v os s n to v os 25 27 ns c i input capacitance 3.5 pf c pd power dissipation capacitance per switch see notes 1 and 2 29 pf c s maximum switch capacitance independent (y) common (z) 5 45 pf note: 1. c pd is used to determine the dynamic power dissipation (p d in m w) p d = c pd v cc 2 f i (c l v cc 2 f o ) where: f i = input frequency in mhz; c l = output load capacity in pf; f o = output frequency in mhz; c s = max. switch capacitance in pf; v cc = supply voltage in v; (c l v cc 2 f o ) = sum of the outputs. 2. the condition is v i = gnd to v cc . ordering information packages temperature range outside north america north america pkg. dwg. # 24-pin plastic dil 40 c to +125 c 74lv4067 n 74lv4067 n sot101-1 24-pin plastic so 40 c to +125 c 74lv4067 d 74lv4067 d sot137-1 24-pin plastic ssop type ii 40 c to +125 c 74lv4067 db 74lv4067 db sot340-1 24-pin plastic tssop type i 40 c to +125 c 74lv4067 pw 74lv4067pw dh sot355-1
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 3 pin configuration sv01621 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 z y 7 y 6 y 5 y 4 y 3 y 2 y 1 y 0 s 0 s 1 v cc y 8 y 9 y 10 y 11 y 12 y 13 y 15 y 14 e s 2 s 3 gnd pin description pin number symbol function 1 z common input/output 9, 8, 7, 6, 5, 4, 3, 2, 23, 22, 21, 20, 19, 18, 17, 16 y 0 to y 15 independent inputs/outputs 10, 11, 14, 13 s 0 to s 3 select inputs 12 gnd ground (0 v) 15 e enable input (active low) 24 v cc positive supply voltage logic symbol (ieee/iec) sv01624 mdx 15 11 14 13 10 0 3 g16 9 8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 4 7 3 6 2 5 23 22 21 20 19 18 17 16 16x 0 15 1 logic symbol sv01622 10 14 15 s 0 z s 2 13 s 3 11 s 1 e 1 y 7 2 y 15 16 y 2 7 y 10 21 y 1 8 y 9 22 y 3 6 y 11 20 y 0 9 y 8 23 y 5 4 y 13 18 y 4 5 y 12 19 y 6 3 y 14 17
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 4 function table inputs channel e s 3 s 2 s 1 s 0 on l l l l l y 0 z l l l l h y 1 z l l l h l y 2 z l l l h h y 3 z l l h l l y 4 z l l h l h y 5 z l l h h l y 6 z l l h h h y 7 z l h l l l y 8 z l h l l h y 9 z l h l h l y 10 z l h l h h y 11 z l h h l l y 12 z l h h l h y 13 z l h h h l y 14 z l h h h h y 15 z h x x x x none notes: h = high voltage level l = low voltage level x = don't care functional diagram sv01625 y 1 y 10 y 11 y 13 y 12 y 14 y 15 y 2 y 3 y 4 y 5 y 6 y 7 y 8 y 9 8 7 6 5 4 3 2 23 22 21 20 18 19 17 16 9 1 y 0 11 14 10 13 15 s 1 s 2 s 0 s 3 e z 24 v cc 12 gnd 1-of-16 decoder schematic diagram (one switch) sv01626 gnd y n z v cc v cc
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 5 logic diagram sv01630 y 0 s 0 s 1 s 2 s 3 e y 1 y 2 y 3 y 4 y 5 y 6 y 7 y 8 y 9 y 10 y 11 y 12 y 13 y 14 z y 15
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 6 absolute maximum ratings 1, 2 in accordance with the absolute maximum rating system (iec 134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions rating unit v cc dc supply voltage 0.5 to +7.0 v i ik dc input diode current v i < 0.5 or v i > v cc + 0.5 v 20 ma i sk dc switch diode current v s < 0.5 or v s > v cc + 0.5 v 20 ma i s dc switch current 0.5 v < v s < v cc + 0.5 v 25 ma t stg storage temperature range 65 to +150 c p tot power dissipation per package plastic dil plastic mini-pack (so) plastic shrink mini-pack (ssop and tssop) for temperature range: 40 to +125 c above +70 c derate linearly with 12 mw/k above +70 c derate linearly with 8 mw/k above +60 c derate linearly with 5.5 mw/k 750 500 400 mw notes: 1. stresses beyond those listed may cause permanent damage to the device. these are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under arecommended operating conditionso is not implied. exposur e to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. the input and output voltage ratings may be exceeded if the input and output current ratings are observed. recommended operating conditions symbol parameter conditions min typ max unit v cc dc supply voltage see note 1 and figure 5 1.0 3.3 6.0 v v i input voltage 0 v cc v v o output voltage 0 v cc v t amb operating ambient temperature range in free air see dc and ac characteristics 40 40 +85 +125 c t r , t f input rise and fall times v cc = 1.0 v to 2.0 v v cc = 2.0 v to 2.7 v v cc = 2.7 v to 6.0 v 500 200 100 ns/v note: 1. the lv is guaranteed to function down to v cc = 1.0v (input levels gnd or v cc ); dc characteristics are guaranteed from v cc = 1.2v to v cc = 6.0v.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 7 dc electrical characteristics over recommended operating conditions, voltages are referenced to gnd (ground = 0 v) limits symbol parameter test conditions -40 c to +85 c -40 c to +125 c unit min typ 1 max min max v cc = 1.2 v 0.9 0.9 high level input v cc = 2.0 v 1.4 1.4 v ih high l eve l i npu t voltage v cc = 2.7 to 3.6 v 2.0 2.0 v voltage v cc = 4.5 v 3.15 3.15 v cc = 6.0 v 4.20 4.20 v cc = 1.2 v 0.3 0.3 low level input v cc = 2.0 v 0.6 0.6 v il low l eve l i npu t voltage v cc = 2.7 to 3.6 v 0.8 0.8 v voltage v cc = 4.5 v 1.35 1.35 v cc = 6.0 v 1.80 1.80 i i input leakage v cc = 3.6 v i =v cc or gnd 1.0 1.0 m a i i g current v cc = 6.0 v i = v cc or gnd 2.0 2.0 m a i s analog switch off-state current v cc = 3.6 v i = v ih or v il iv iv gnd 1.0 1.0 m a i s off - state current per channel v cc = 6.0 iv s i = v cc - g nd (see figure 2) 2.0 2.0 m a i s analog switch v cc = 3.6 v i = v ih or v il iv iv gnd 1.0 1.0 m a i s g on-state current v cc = 6.0 iv s i = v cc - gnd (see figure 3) 2.0 2.0 m a i cc quiescent supply v cc = 3.6 v v i = v cc or gnd v gnd v 20.0 40 m a i cc y current v cc = 6.0 v v is = g nd or v cc ; v os = v cc or gnd 40.0 80 m a d i cc additional quiescent supply current per input v cc = 2.7 to 3.6 v v i = v cc 0.6 v 500 850 m a v cc = 1.2 v v i = v ih or v il; i s = 100 a; v is = v cc to gnd on - resistance v cc = 2.0 v 145 325 375 r on on-resistance (peak) v cc = 2.7 v v i = v ih or v il ; 90 200 235 () v cc = 3.0 to 3.6 v v i v ih or v il i s = 1000 a; v v t gnd 80 180 210 v cc = 4.5 v v is = v cc to gnd 60 135 160 v cc = 6.0 v 55 125 145 v cc = 1.2 v v i = v ih or v il; i s = 100 a; v is = gnd 225 on - resistance v cc = 2.0 v 110 235 270 r on on-resistance (rail) v cc = 2.7 v v i = v ih or v il ; 70 145 165 () v cc = 3.0 to 3.6 v v i v ih or v il i s = 1000 a; v gnd 60 130 150 v cc = 4.5 v v is = gnd 45 100 115 v cc = 6.0 v 40 85 100 notes: 1. all typical values are measured at t amb = 25 c. 2. at supply voltages approaching 1.2 v, the analog switch on-resistance becomes extremely non-linear. therefore, it is recommen ded that these devices be used to transmit digital signals only, when using these supply voltages. 3. r on (max) data is preliminary.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 8 dc electrical characteristics ( continued ) limits symbol parameter test conditions -40 c to +85 c -40 c to +125 c unit min typ 1 max min max v cc = 1.2 v v i = v ih or v il; i s = 100 a; v is = v cc 250 r on - resistance v cc = 2.0 v 120 320 370 r on on resistance (rail) v cc = 2.7 v v i = v ih or v il ; 75 195 225 () v cc = 3.0 to 3.6 v i ih il i s = 1000 a; v v 70 175 205 v cc = 4.5 v v is = v cc 50 130 150 v cc = 6.0 v 45 120 135 v cc = 1.2 v maximum variation v cc = 2.0 v 5 r on maximum variation of on-resistance b v cc = 2.7 v v i = v ih or v il; 4 r on between any two channels v cc = 3.0 to 3.6 v i ih il v is = v cc to gnd 4 channels v cc = 4.5 v 3 v cc = 6.0 v 2 notes: 1. all typical values are measured at t amb = 25 c. 2. at supply voltages approaching 1.2 v, the analog switch on-resistance becomes extremely non-linear. therefore, it is recommen ded that these devices be used to transmit digital signals only, when using these supply voltages. 3. r on (max) data is preliminary.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 9 sv01623 v high (from enable inputs) i is z gnd y n v is = 0 to v cc gnd figure 1. test circuit for measuring on-resistance (r on ). sv01628 a low (from enable inputs) z gnd y n v i = v cc or gnd v o = gnd or v cc a figure 2. test circuit for measuring off-state current. sv01629 high (from enable inputs) z gnd y n v i = v cc or gnd vo (open circuit) a a figure 3. test circuit for measuring on-state current. sv01627 0 v cc = 2.0 v v cc = 3.0 v v cc = 4.5 v 0 1.2 2.4 3.6 v is (v) 4.8 60 30 120 90 150 r on ( ) figure 4. typical on-resistance (r on ) as a function of input voltage (v is for v is = 0 to v cc gnd. sv01631 0 2.0 4.0 6.0 2.0 4.0 6.0 v cc gnd (v) v cc gnd (v) operating area figure 5. guaranteed operating area as a function of the supply voltages.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 10 ac characteristics gnd = 0 v; t r = t f 2.5ns; c l = 50pf condition limits symbol parameter condition 40 to +85 c 40 to +125 c unit symbol parameter v cc (v) other min typ 1 max min max unit 1.2 30 2.0 10 19 24 t phl/ t plh propagation delay v i to v 2.7 r l = ; c l =50 p f 8 14 18 ns t phl/ t plh v is to v os z to y n 3.0 to 3.6 c l = 50 pf fi g ure 13 6 2 11 14 ns n 4.5 figure 13 5 9 12 6.0 4 7 9 1.2 45 2.0 r ; 15 31 36 t phl/ t plh propagation delay v i to v 2.7 r l = ; c l =50 p f 11 23 26 ns t phl/ t plh v is to v os y n to z 3.0 to 3.6 c l = 50 pf figure 13 9 2 18 21 ns n 4.5 figure 13 8 15 18 6.0 6 12 14 1.2 145 2.0 r l = 1k 49 94 112 t pzh /t pzl turn-on time 2.7 r l = 1k c l = 50 pf 36 69 86 ns t pzh /t pzl e to y n 3.0 to 3.6 figures 14 and 15 28 2 55 66 ns 4.5 an d 15 25 47 56 6.0 19 38 43 1.2 160 2.0 r l = 1k 54 102 122 t pzh /t pzl turn-on time 2.7 r l = 1k c l = 50 pf 40 75 94 ns t pzh /t pzl z to y n 3.0 to 3.6 figures 14 and 15 30 2 60 72 ns 4.5 an d 15 27 51 61 6.0 21 39 47 1.2 125 2.0 r l = 1k 43 80 95 t phz /t plz turn-off time 2.7 r l = 1k c l = 50 pf 33 59 71 ns t phz /t plz e to y n 3.0 to 3.6 figures 14 and 15 26 2 48 57 ns 4.5 an d 15 23 41 49 6.0 18 32 38 1.2 140 2.0 r l = 1k 49 90 109 t phz /t plz turn-off time 2.7 r l = 1k c l = 50 pf 37 67 81 ns t phz /t plz sn to y n 3.0 to 3.6 figures 14 and 15 29 2 54 65 ns 4.5 an d 15 26 46 56 6.0 20 36 43 notes: 1. unless otherwise stated, all typical values are measured at t amb = 25 c 2. typical values are measured at v cc = 3.3 v.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 11 ac characteristics (continued) gnd = 0 v; t r = t f 2.5ns; c l = 50pf condition 40 to +85 c 40 to +125 c symbol parameter v cc (v) other min typ 1 max min max unit 1.2 145 2.0 r l = 1k 51 93 110 t pzh /t pzl turn-on time 2.7 r l = 1k c l = 50 pf 39 70 83 ns t pzh /t pzl e to z 3.0 to 3.6 figures 14 and 15 29 2 56 66 ns 4.5 an d 15 26 48 56 6.0 20 36 43 1.2 170 2.0 r l = 1k 58 109 131 t pzh /t pzl turn-on time 2.7 r l = 1k c l = 50 pf 42 80 96 ns t pzh /t pzl s n to y n 3.0 to 3.6 figures 14 and 15 32 2 64 77 ns 4.5 an d 15 29 54 65 6.0 21 42 50 1.2 145 2.0 r l = 1k 51 93 110 t phz /t plz turn-off time 2.7 r l = 1k c l = 50 pf 38 69 82 ns t phz /t plz e to z 3.0 to 3.6 figures 14 and 15 30 2 56 66 ns 4.5 an d 15 29 48 56 6.0 21 37 44 1.2 160 2.0 r l = 1k 56 104 124 t phz /t plz turn-off time 2.7 r l = 1k c l = 50 pf 42 77 92 ns t phz /t plz s n to y n 3.0 to 3.6 figures 14 and 15 32 2 62 74 ns 4.5 an d 15 29 53 61 6.0 23 41 49 notes: 1. unless otherwise stated, all typical values are measured at t amb = 25 c 2. typical values are measured at v cc = 3.3 v.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 12 additional ac characteristics recommended conditions and typical values gnd = 0 v; t r = t f 2.5ns symbol parameter typ. unit v cc (v) v is(pp) (v) conditions sine-wave distortion f = 1 khz 0.80 0.40 % 3.0 6.0 2.75 5.50 r l = 10 k ; c l = 50 pf figures 10 and 11 sine-wave distortion f = 10 khz 2.40 1.20 % 3.0 6.0 2.75 5.50 r l = 10 k ; c l = 50 pf figures 10 and 11 switch aoffo signal feed through 50 50 db 3.0 6.0 note 1 r l = 600 ; c l = 50 pf; f= 1 mhz figures 6 and 12 crosstalk between any two switches/multiplexers 60 60 db 3.0 6.0 note 1 r l = 600 ; c l = 50 pf; f= 1 mhz figure 8 v (pp) crosstalk voltage between enable or address input to any switch (peak-to-peak value) 110 120 mv 3.0 6.0 r l = 600 ; c l = 50 pf; f= 1 mhz (s n or e , square wave between v cc and gnd t r = t f = 6 ns) figure 9 f max minimum frequency response (3 db) 180 200 mhz 3.0 6.0 note 2 r l = 50 ; c l = 50 pf figures 7 and 10 c s maximum switch capacitance 5 pf general notes: v is is the input voltage at ny or z terminal, whichever is assigned as an input. v os is the output voltage at ny or z terminal, whichever is assigned as an output. notes: 1. adjust input voltage v is is 0 dbm level (0 dbm = 1 mw into 600 2. adjust input voltage v is is 0 dbm level at v os for 1 mhz (0 dbm = 1 mw into 50 sv01635 (db) f (khz) 0 10 10 2 10 3 10 4 10 5 10 6 50 100 figure 6. typical switch aoffo signal feed-through as a function of frequency. sv01636 (db) f (khz) 5 10 10 2 10 3 10 4 10 5 10 6 0 5 figure 7. typical frequency response. notes to figures 6 and 7: test conditions: v cc = 3.0 v; gnd = 0 v; r l = 50 ; r source = 1k . sv01632 gnd 2r l v cc channel on v is 0.1 f r l y n /z z/y n c l gnd channel off (b) (a) v os db 2r l y n /z 2r l 2r l v cc v cc z/y n 2r l c l r l figure 8. test circuit for measuring crosstalk between any two switches. (a) channel on condition; (b) channel off condition.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 13 note to figure 9: the crosstalk is defined as follows (oscilloscope output): sv01642 v(p p) sv01633 gnd s n or e z/y n oscilloscope dut c l 2r l 2r l v cc v cc 2r l y n /z 2r l figure 9. test circuit for measuring crosstalk between control and any switch. sv01634 gnd channel on v os db y n /z 2r l v cc z/y n 2r l c l 0.1 f sine-wave figure 10. test circuit for measuring minimum frequency response. note to figure 10: adjust input voltage to obtain 0 dbm at v os when f in = 1 mhz. after set-up frequency of f in is increased to obtain a reading of 3 db at v os. sv01637 gnd channel on v os distortion meter y n /z 2r l v cc z/y n 2r l c l 10 f f in = 1 khz sine-wave figure 11. test circuit for measuring sine-wave distortion. sv01639 gnd 2r l v cc channel off v is 0.1 f y n /z z/y n db c l 2r l v os figure 12. test circuit for measuring switch aoffo signal feed-through.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 14 waveforms v m = 1.5 v at 2.7 v v cc 3.6 v v m = 0.5 v cc at 2.7 v > v cc > 3.6 v v ol and v oh are the typical output voltage drop that occur with the output load v x = v ol + 0.3 v at 2.7 v v cc 3.6 v v x = v ol + 0.1 v cc at 2.7 v > v cc > 3.6 v v y = v oh 0.3 v at 2.7 v v cc 3.6 v v y = v oh 0.1 v cc at 2.7 v > v cc > 3.6 v sv01638 v m v m inputs outputs gnd v ol v i v oh t phl t plh figure 13. input (v is ) to output (v os ) propagation delays. sv01640 outputs disabled outputs enabled outputs enabled t phz t pzh t pzl t plz v x v y v m v m v m inputs output high-to-off off-to-high output low-to-off off-to-low gnd v cc v i v ol v oh gnd figure 14. turn-on and turn-off times for the inputs (s n , e ) to the output (v os ). test circuit v m v m t w negative pulse 10% 10% 90% 90% 0v v m v m t w v i positive pulse 90% 90% 10% 10% 0v t thl (t f ) t tlh (t r )t thl (t f ) t tlh (t r ) sy01740 pulse generator r t v l d.u.t. v o c l v cc 1k test circuit for outputs open gnd s 1 2 v cc definitions v cc v i < 2.7v 2.7 - 3.6v v cc 2.7v test s 1 t plz/ t pzl t plh/ t phl t phz /t pzh 2 v cc open gnd > 3.6 v v cc c l = load capacitance includes jig and probe capacitance r t = termination resistance should be equal to z out of pulse generators. v i v is pulse gnd v i t r =t f =6ns, when measuring f max, there is no constraint on t r , t f with 50% duty factor. 1k 50 pf r l = load resistor figure 15. load circuitry for switching times.
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 15 dip24: plastic dual in-line package; 24 leads (600 mil) sot101-1
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 16 so24: plastic small outline package; 24 leads; body width 7.5 mm sot137-1
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 17 ssop24: plastic shrink small outline package; 24 leads; body width 5.3 mm sot340-1
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 18 tssop24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm sot355-1
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer 1998 jun 23 19 notes
philips semiconductors product specification 74lv4067 16-channel analog multiplexer/demultiplexer yyyy mmm dd 20 philips semiconductors and philips electronics north america corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performanc e. philips semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under a ny patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copy right, or mask work right infringement, unless otherwise specified. applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. life support applications philips semiconductors and philips electronics north america corporation products are not designed for use in life support appl iances, devices, or systems where malfunction of a philips semiconductors and philips electronics north america corporation product can reasonab ly be expected to result in a personal injury. philips semiconductors and philips electronics north america corporation customers using or sel ling philips semiconductors and philips electronics north america corporation products for use in such applications do so at their own risk and agree to fully indemnify philips semiconductors and philips electronics north america corporation for any damages resulting from such improper use or sale. this data sheet contains preliminary data, and supplementary data will be published at a later date. philips semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. philips semiconductors 811 east arques avenue p.o. box 3409 sunnyvale, california 940883409 telephone 800-234-7381 definitions data sheet identification product status definition objective specification preliminary specification product specification formative or in design preproduction product full production this data sheet contains the design target or goal specifications for product development. specifications may change in any manner without notice. this data sheet contains final specifications. philips semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. ? copyright philips electronics north america corporation 1998 all rights reserved. printed in u.s.a. print code date of release: 05-96 document order number: 9397-750-04661

▲Up To Search▲

Price & Availability of 74LV4067PWDH

	To Download 74LV4067PWDH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .